Upgrade Gold to Platinum Kit

STOP!!

YOU MUST ENSURE YOUR FIREARM IS FULLY UNLOADED AND PROVED SAFE BEFORE USING!!

PROVE
POINT THE FIREARM IN THE SAFEST AVAILABLE DIRECTION.
REMOVE ALL AMMUNITION.
OBSERVE THE CHAMBER.
VERIFY THE FEEDING PATH.
EXAMINE THE BORE.

ONCE SAFE, YOU MAY PROCEED TO THE NEXT STEP.

!! SAFETY WEAR: THIS INSTALLATION INVOLVES SPRINGS THAT CAN SHOOT OUT IF INSTALLED IMPROPERLY. YOU MUST WEAR EYEWEAR TO PROTECT YOURSELF WHILE INSTALLTING.

!! AMMUNITION WARNING: WE RECOMMEND REMOVING ALL LIVE AMMUNITION FROM YOUR WORKING AREA WHILE PERFORMING ANY MODIFICATIONS TO YOUR FIREARM.


FIRST, ENSURE YOU HAVE THE COMPLETE UPGRADE KIT.
LTAC - Raven GOLD to PLATINUM Upgrade Kit - Glock 9MM


THE REQUIRED TOOLS TO COMPLETE THIS UPGRADE ARE ALL INCLUDED:
ALL PARTS MUST BE INSTALLED IN THE CORRECT ORDER!

MAKE SURE TO HAVE (1) OR (2) EMPTY MAGAZINES ON HAND TO PROPERLY FUNCTION TEST THE PARTS AFTER THE INSTALLATION IS COMPLETE.


STEP 1: FULLY CLEAN YOUR RAVEN. NEXT, DETACH THE MAGWELL FROM YOUR RAVEN SO THAT THESE PARTS CAN BE INSTALLED WITH EASE.


STEP 2: INSTALL THE BOLT CATCH SPRING AND PLUNGER.
NOTE: THE ROUNDED PART OF THE PLUNGER MUST FACE OUTWARDS.


STEP 3: INSTALL THE LEFT HAND BOLT CATCH SYSTEM INTO PLACE AS SHOWN
NOTE: ALL PARTS SHOULD DROP IN EASILY! DO NOT FORCE ANY PARTS INTO POSITION!


STEP 4: INSTALL THE MAGWELL COVER / BOLT STOP BLOCK AND SECURE IT WITH THE INCLUDED HARDWARE. INSTALL THE HARDWARE UNTIL SNUG, THEN ADD A 1/4 TURN.
NOTE: THE HARDWARE SHOULD BE TIGHT. DO NOT OVER TIGHTEN TO STRIP THE THREADS IN THE MAGWELL.


STEP 5: FUNCTION TEST THE LEFT HAND BOLT CATCH SYSTEM BY PRESSING ON THE BOLT CATCH STUD AND RELEASE IT. IT SHOULD MOVE EASILY AND IMMEDIATELY SPRING BACK TO ITS RESTING POSITION.


STEP 6: INSERT AND HOLD THE RIGHT HAND BOLT CATCH IN POSITON. SIMULTANEOUSLY INSERT THE BUTTON RETAINING PIN. TIGHTEN UNTIL SNUG. YOU MAY WANT TO ADD A TINY BIT OF BLUE LOCTITE TO THE THREADS TO ENSURE THEY NEVER WALK OUT.


STEP 7: FUNCTION TEST THE RIGHT HAND BOLT CATCH SYSTEM BY PRESSING ON THE BOLT CATCH STUD AND RELEASE IT. IT SHOULD MOVE EASILY AND IMMEDIATELY SPRING BACK TO ITS RESTING POSITION. IT SHOULD CAUSE BOTH THE LEFT AND RIGHT SIDE BOLT CATCH TO ACTIVATE AND DEACTIVATE.


STEP 8: REMOVE THE BUTTON RETAINING PIN SECURING THE RIGHT SIDE MAGAZINE RELEASE. NOTE! THE MAGAZINE RELEASE SPRING IS INSIDE AND WILL SHOOT OUT. NOTE: BE CAREFUL NOT TO LOSE THE SPRING AND OR HAVE IT HIT YOU IN THE FACE. ONCE THE RETAINING PIN IS UNTHREADED AS MUCH AS POSSIBLE IT MAY STILL STAY RETAININED IN THE MAGWELL. YOU CAN USE YOUR FINGERS OR A TOOL SUCH AS PLIERS GENTLY TO FINISH PULLING IT OUT.


STEP 9: INSERT THE LEFT SIDE MAGAZINE RELEASE BUTTON AND HOLD IT IN POSITION WHILE SIMULTANEOUSLY INSTALLING THE MAGAZINE RELEASE RETAINING PIN. TIGHTEN UNTIL SNUG AND THEN GIVE IT ANOTHER 1/4 TURN.
NOTE: BE CAREFUL TO INSTALL THE CROSSPIN STRAIGHT AS TO ENSURE IT DOES NOT GET CROSS THREADED AND DAMAGED!


STEP 10: REPLACE THE MAGAZINE CATCH SPRING AND REINSTALL THE RIGHT HAND MAGAZINE CATCH. TIGHTEN THE RETAINING PIN UNTIL SNUG.


STEP 11: INSERT AN EMPTY MAGAZINE AND FUNCTION TEST THE LEFT SIDE MAGAZINE RELEASE BUTTON. ENSURE THE MAGAZINE RELEASES. NEXT, REINSERT THE EMPTY MAGAZINE AND FUNCTION TEST THE RIGHT MAGAZINE RELEASE BUTTON. ENSURE THE MAGAZINE RELEASES


STEP 12: FINAL FUNCTION TEST. REINSTALL THE COMPLETED MAGWELL BACK ONTO YOUR RAVEN, INSERT AN EMPTY MAGAZINE AND PULL FULLY REARWARD ON THE CHARGING HANDLE. THE BOLT CATCH FUNCTION SHOULD OPERATE. NEXT PRESS THE LEFT HAND MAGAZINE RELEASE AND THE MAGAZINE SHOULD RELEASE.
PRESS THE BOLT CATCH RELEASE BUTTON AND THE BOLT SHOULD FULLY CLOSE INTO BATTERY AGAIN.


THE INSTALLATION IS NOW FULLY COMPLETE.